View PS2562L-1-F3-A_478352.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PHOTOCOUPLER
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
HIGH ISOLATION VOLTAGE DARLINGTON TRANSISTOR TYPE MULTI PHOTOCOUPLER SERIES
DESCRIPTION
The PS2562-1 is optically coupled isolators containing a GaAs light emitting diode and an NPN silicon darlington connected phototransistor. The PS2562-1 is in a plastic DIP (Dual In-line Package) and the PS2562L-1 is lead bending type (Gull-wing) for surface mount. The PS2562L1-1 is lead bending type for long creepage distance. The PS2562L2-1 is lead bending type for long creepage distance (Gull-wing) for surface mount. -NEPOC Series-
FEATURES
* High isolation voltage (BV = 5 000 Vr.m.s.) * High current transfer ratio (CTR = 2 000 % TYP.) * High-speed switching (tr, tf = 100 s TYP.) * Ordering number of tape product: PS2562L-1-E3, E4, F3, F4, PS2562L2-1-E3, E4 * Safety standards * UL approved: File No. E72422 * BSI approved: No. 7112/7420 * CSA approved: No. CA 101391 * NEMKO approved: No. P03200272 * SEMKO approved: No. 303059 * DEMKO approved: No. 312341 * FIMKO approved: No. FI 10620 * DIN EN60747-5-2 (VDE0884 Part2) approved (option)
APPLICATIONS
* Power supply * Telephone/FAX. * FA/OA equipment * Programmable logic controller
Document No. PN10235EJ03V0DS (3rd edition) Date Published March 2006 CP(K)
The mark
shows major revised points. (c) NEC Compound Semiconductor Devices, Ltd. 1992, 2006
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
PACKAGE DIMENSIONS (UNIT : mm) DIP Type (New package)
PS2562-1
4.60.35 4
TOP VIEW
3 1. Anode 2. Cathode 3. Emitter 4. Collector
6.50.5
1
2 7.62
3.20.4 4.150.4
3.50.3
1.250.15
0 to 15 +0.1 0.25 -0.05 0.500.10 0.25 M 2.54
DIP Type
PS2562-1
4.60.5 4
TOP VIEW
3 1. Anode 2. Cathode 3. Emitter 4. Collector
6.50.5
1
2 7.62
3.30.5 4.150.4
3.50.3
1.250.15
0 to 15 +0.1 0.25 -0.05 0.500.10 0.25 M 2.54
2
Data Sheet PN10235EJ03V0DS
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
Lead Bending Type (New package)
PS2562L-1
4.60.35
TOP VIEW
4 3 1. Anode 2. Cathode 3. Emitter 4. Collector 1 2
6.50.5
0.25 +0.1 -0.05
3.50.3
1.250.15 0.25 M 2.54 0.15
0.90.25 9.600.4
Lead Bending Type
PS2562L-1
4.60.5
TOP VIEW
4 3 1. Anode 2. Cathode 3. Emitter 4. Collector 1 2
6.50.5
0.25 +0.1 -0.05
3.50.3
1.250.15 0.25 M 2.54 0.15
0.90.25 9.600.4
0.1 +0.1 -0.05
0.1 +0.1 -0.05
Data Sheet PN10235EJ03V0DS
3
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
Lead Bending Type For Long Creepage Distance (New Package)
PS2562L1-1
4.60.35 4
6.50.5
TOP VIEW
4 3 1. Anode 2. Cathode 3. Emitter 4. Collector 1 2 10.16
3
1
3.15 3.85 0.35 0.4 3.5 0.3
2
0.500.1 0.25 M 2.54 0.25-0.05
+0.1
1.250.15
0 to 15
Lead Bending Type For Long Creepage Distance
PS2562L1-1
4.60.5
TOP VIEW
4 3 1. Anode 2. Cathode 3. Emitter 4. Collector 1 2 10.16
3.150.35 3.850.4
3.50.3
6.50.5
0 to 15
0.25 +0.1 -0.05
1.250.15 0.500.10 0.25 M 2.54
4
Data Sheet PN10235EJ03V0DS
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
Lead Bending Type For Long Creepage Distance (Gull-Wing) (New Package)
PS2562L2-1
4.60.35 4
6.50.5
TOP VIEW
4 3 3 1. Anode 2. Cathode 3. Emitter 4. Collector 1
0.250.2
2
0.25-0.05
+0.1
1
3.50.3
2
1.250.15 0.25 M 2.54
0.25
0.90.25 10.16 11.8-0.5
+0.2
Lead Bending Type For Long Creepage Distance (Gull-Wing)
PS2562L2-1
4.60.5
TOP VIEW
4 3 1. Anode 2. Cathode 3. Emitter 4. Collector 1 2 10.16
0.250.2
6.50.5
3.50.3
0.25 +0.1 -0.05
1.250.15 0.25 M 2.54 0.25
0.90.25 11.8 +0.2 -0.5
Data Sheet PN10235EJ03V0DS
5
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
MARKING EXAMPLE
No. 1 pin Mark
2562 ML601
Assembly Lot
M
L
6 01
Week Assembled Year Assembled (Last 1 Digit) In-house Code CTR Rank Code
Package Standard PKG New PKG
Made in Japan Made in Taiwan
L
J
6
Data Sheet PN10235EJ03V0DS
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
ORDERING INFORMATION
Part Number Order Number Solder Plating Specification PS2562-1 PS2562L-1 PS2562L1-1 PS2562L2-1 PS2562L-1-E3 PS2562L-1-E4 PS2562L-1-F3 PS2562L-1-F4 PS2562L2-1-E3 PS2562L2-1-E4 PS2562-1-V PS2562L-1-V PS2562L1-1-V PS2562-1-A PS2562L-1-A PS2562L1-1-A PS2562L2-1-A PS2562L-1-E3-A PS2562L-1-E4-A PS2562L-1-F3-A PS2562L-1-F4-A PS2562L2-1-E3-A PS2562L2-1-E4-A PS2562-1-V-A PS2562L-1-V-A PS2562L1-1-V-A Magazine case 100 pcs DIN EN60747-5-2 (VDE0884 Part2) approved products PS2562L2-1-V PS2562L-1-V-E3 PS2562L-1-V-E4 PS2562L-1-V-F3 PS2562L-1-V-F4 PS2562L2-1-V-E3 PS2562L2-1-V-E4 PS2562L2-1-V-A PS2562L-1-V-E3-A PS2562L-1-V-E4-A PS2562L-1-V-F3-A PS2562L-1-V-F4-A PS2562L2-1-V-E3-A PS2562L2-1-V-E4-A Embossed Tape 1 000 pcs/reel Embossed Tape 2 000 pcs/reel Embossed Tape 1 000 pcs/reel (option) Embossed Tape 1 000 pcs/reel Embossed Tape 2 000 pcs/reel Embossed Tape 1 000 pcs/reel Pb-Free Magazine case 100 pcs Packing Style Safety Standard Approval Standard products (UL, CSA, BSI, NEMKO, SEMKO, DEMKO, FIMKO approved) Application Part Number PS2562-1
*1
*1 For the application of the Safety Standard, following part number should be used.
Data Sheet PN10235EJ03V0DS
7
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
ABSOLUTE MAXIMUM RATINGS (TA = 25C, unless otherwise specified)
Parameter Diode Reverse Voltage Forward Current (DC) Power Dissipation Derating Power Dissipation Peak Forward Current Transistor
*1
Symbol VR IF
Ratings 6 80 1.5 150 1 40 6 200 2.0 200 5 000 -55 to +100 -55 to +150
Unit V mA mW/C mW A V V mA mW/C mW Vr.m.s. C C
PD/C
PD IFP VCEO VECO IC
Collector to Emitter Voltage Emitter to Collector Voltage Collector Current Power Dissipation Derating Power Dissipation
PC/C
PC BV TA Tstg
Isolation Voltage
*2
Operating Ambient Temperature Storage Temperature
*1 PW = 100 s, Duty Cycle = 1% *2 AC voltage for 1 minute at TA = 25C, RH = 60% between input and output Pins 1-2 shorted together, 3-4 shorted together.
8
Data Sheet PN10235EJ03V0DS
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
ELECTRICAL CHARACTERISTICS (TA = 25C)
Parameter Diode Forward Voltage Reverse Current Terminal Capacitance Transistor Collector to Emitter Dark Current Coupled Current Transfer Ratio (IC/IF)
*1
Symbol VF IR Ct ICEO IF = 10 mA VR = 5 V
Conditions
MIN.
TYP. 1.17
MAX. 1.4 5
Unit V
A
pF
V = 0 V, f = 1.0 MHz VCE = 40 V, IF = 0 mA
50 400
nA
CTR
IF = 1 mA, VCE = 2 VDC
200
2 000
%
Collector Saturation Voltage Isolation Resistance Isolation Capacitance Rise Time Fall Time
*2
VCE(sat)
IF = 1 mA, IC = 2 mA
11
1.0
V
RI-O CI-O tr tf
VI-O = 1.0 kVDC V = 0 V, f = 1.0 MHz VCC = 10 V, IC = 10 mA, RL = 100
10
0.5 100 100
pF
s
*2
*1 CTR rank K : 2 000 to L: M: (%) 700 to 3 400 (%) 200 to 1 000 (%)
*2 Test circuit for switching time
Pulse Input PW = 1 ms Duty Cycle = 1/10 IF 50 VOUT RL = 100 VCC
Data Sheet PN10235EJ03V0DS
9
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
TYPICAL CHARACTERISTICS (TA = 25 C, unless otherwise specified)
DIODE POWER DISSIPATION vs. AMBIENT TEMPERATURE
Transistor Power Dissipation PC (mW)
TRANSISTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE
200
150
Diode Power Dissipation PD (mW)
150 2 mW/C 100
100 1.5 mW/C
50
50
0
25
50
75
100
125
150
0
25
50
75
100
125
150
Ambient Temperature TA (C)
Ambient Temperature TA (C)
FORWARD CURRENT vs. FORWARD VOLTAGE
100 50
Forward Current IF (mA)
COLLECTOR CURRENT vs. COLLECTOR TO EMITTER VOLTAGE
160 5 mA 140
Collector Current IC (mA)
TA = +100 C +60 C +25 C
120 100 80 60 40 20 1 mA IF = 0.5 mA 2 4 6 8 10 2 mA
10 5 1 0.5 0 C -25 C -55 C
0.1 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5
0
Forward Voltage VF (V)
Collector to Emitter Voltage VCE (V)
COLLECTOR TO EMITTER DARK CURRENT vs. AMBIENT TEMPERATURE
Collector to Emitter Dark Current ICEO (nA)
COLLECTOR CURRENT vs. COLLECTOR SATURATION VOLTAGE
200 5 mA 2 mA 1 mA 10 5 0.5 mA 100
Collector Current IC (mA)
10 000 VCE = 2 V 5V 10 V 24 V 40 V
50
1000
100
10
0.2 mA 1 0.5 0.2 0.4 IF = 0.1 mA
1 -50 -25 0 25 50 75 100
0.6
0.8
1.0
1.2
1.4
1.6
Ambient Temperature TA (C)
Collector Saturation Voltage VCE(sat) (V)
Remark
The graphs indicate nominal characteristics.
Data Sheet PN10235EJ03V0DS
10
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
NORMALIZED CURRENT TRANSFER RATIO vs. AMBIENT TEMPERATURE
Normalized Current Transfer Ratio CTR
CURRENT TRANSFER RATIO vs. FORWARD CURRENT
8 000
Current Transfer Ratio CTR (%)
1.4 1.2 1.0 0.8 0.6 0.4 0.2 -50 -25 0 25 50 75 100 Normalized to 1.0 at TA = 25 C, IF = 1 mA, VCE = 2 V
VCE = 2 V 7 000 6 000 Sample A B C 5 000 D 4 000 3 000 2 000 1 000 0 0.1 0.5 1 5 10 30
Ambient Temperature TA (C)
Forward Current IF (mA)
SWITCHING TIME vs. LOAD RESISTANCE
1 000
Current Transfer Ratio CTR (%)
CURRENT TRANSFER RATIO vs. FORWARD CURRENT
3 000 VCE = 2 V 2 500 2 000 1 500 1 000 500 0 Sample A B C D
VCC = 5 V, 500 IC = 2 mA, CTR = 2 280 % tf 100 50 td tr
Switching Time t ( s)
10 5 2 30 50 ts 100 500 1k 5k
10
50
100
500
Load Resistance RL ()
Forward Current IF ( A)
SWITCHING TIME vs. LOAD RESISTANCE
10 000 5 000
Switching Time t ( s)
FREQUENCY RESPONSE
IF = 1 mA, VCE = 2 V
tf
VCC = 5 V, IF = 1 mA, CTR = 2 280 %
Normalized Gain GV
0 -5 -10 -15
RL = 100
1 000 500 ts
100 50 tr
10 td 300 500 1k 5k 10 k 50 k 100 k
-20
0.2
0.5
1
2
5
10 20
50 100 200
Load Resistance RL ()
Frequency f (kHz)
Remark
The graphs indicate nominal characteristics.
Data Sheet PN10235EJ03V0DS
11
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
LONG TERM CTR DEGRADATION
1.2 IF = 1 mA 1.0
CTR (Relative Value)
0.8 0.6 0.4 0.2 0 10
TA = 25 oC TA = 60 oC
102
103
104
105
106
Time (Hr)
Remark
The graph indicates nominal characteristics.
12
Data Sheet PN10235EJ03V0DS
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
TAPING SPECIFICATIONS (UNIT : mm)
Outline and Dimensions (Tape)
2.00.1 4.00.1
1.750.1
1.5 +0.1 -0
4.5 MAX.
7.50.1
16.00.3
1.550.1
8.00.1
10.30.1
5.30.1
4.00.1 0.4
Tape Direction
PS2562L-1-E3 PS2562L-1-E4
Outline and Dimensions (Reel)
2.00.5
2.00.5 13.00.2
R 1.0
21.00.8
80.01.0
2542.0
17.51.0 21.51.0
Packing: 1 000 pcs/reel
15.9 to 19.4 Outer edge of flange
Data Sheet PN10235EJ03V0DS
13
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
Outline and Dimensions (Tape)
2.00.1 4.00.1
1.750.1
1.5 +0.1 -0
4.5 MAX.
16.00.3
7.50.1
1.550.1 8.00.1
10.30.1
5.30.1
4.00.1 0.4
Tape Direction
PS2562L-1-F3 PS2562L-1-F4
Outline and Dimensions (Reel)
2.00.5
2.00.5 13.00.2
R 1.0
21.00.8
3302.0
1001.0
17.51.0 21.51.0
Packing: 2 000 pcs/reel
15.9 to 19.4 Outer edge of flang
14
Data Sheet PN10235EJ03V0DS
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
Outline and Dimensions (Tape)
2.00.1 4.00.1
1.750.1
1.550.1
4.40.2
11.50.1
2.050.1 12.00.1
6.60.2
0.38
Tape Direction
PS2562L2-1-E3 PS2562L2-1-E4
Outline and Dimensions (Reel)
12.350.15
24.00.3
2.00.5
3302.0
2.00.5 13.00.2
R 1.0
21.00.8
1001.0
25.51.0 29.51.0
Packing: 1 000 pcs/reel
23.9 to 27.4 Outer edge of flange
Data Sheet PN10235EJ03V0DS
15
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
NOTES ON HANDLING 1. Recommended soldering conditions
(1) Infrared reflow soldering * Peak reflow temperature * Time of peak reflow temperature * Time of temperature higher than 220C * Time to preheat temperature from 120 to 180C * Number of reflows * Flux 260C or below (package surface temperature) 10 seconds or less 60 seconds or less 12030 s Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.)
Recommended Temperature Profile of Infrared Reflow
Package Surface Temperature T (C)
(heating) to 10 s 260C MAX. 220C to 60 s 180C 120C 12030 s (preheating)
Time (s)
(2) Wave soldering * Temperature * Time * Preheating conditions * Number of times * Flux 260C or below (molten solder temperature) 10 seconds or less 120C or below (package surface temperature) One (Allowed to be dipped in solder including plastic mold portion.) Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by soldering iron * Peak temperature (lead part temperature) * Time (each pins) * Flux 350C or below 3 seconds or less Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead. (b) Please be sure that the temperature of the package would not be heated over 100C.
16
Data Sheet PN10235EJ03V0DS
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
(4) Cautions * Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent.
2. Cautions regarding noise
Be aware that when voltage is applied suddenly between the photocoupler's input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings.
3. Measurement conditions of current transfer ratios (CTR), which differ according to photocoupler
Check the setting values before use, since the forward current conditions at CTR measurement differ according to product. When using products other than at the specified forward current, the characteristics curves may differ from the standard curves due to CTR value variations or the like. Therefore, check the characteristics under the actual operating conditions and thoroughly take variations or the like into consideration before use.
USAGE CAUTIONS
1. Protect against static electricity when handling. 2. Avoid storage at a high temperature and high humidity.
Data Sheet PN10235EJ03V0DS
17
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
SPECIFICATION OF VDE MARKS LICENSE DOCUMENT
Parameter Application classification (DIN VDE 0109) for rated line voltages 300 Vr.m.s. for rated line voltages 600 Vr.m.s. Climatic test class (DIN IEC 68 Teil 1/09.80) Dielectric strength maximum operating isolation voltage Test voltage (partial discharge test procedure a for type test and random test) Upr = 1.2 x UIORM, Pd < 5 pC Test voltage (partial discharge test procedure b for all devices test) Upr = 1.6 x UIORM, Pd < 5 pC Highest permissible overvoltage Degree of pollution (DIN VDE 0109) Clearance distance Creepage distance Comparative tracking index (DIN IEC 112/VDE 0303 part 1) Material group (DIN VDE 0109) Storage temperature range Operating temperature range Isolation resistance, minimum value VIO = 500 V dc at TA = 25 C VIO = 500 V dc at TA MAX. at least 100 C Safety maximum ratings (maximum permissible in case of fault, see thermal derating curve) Package temperature Current (input current IF, Psi = 0) Power (output or total power dissipation) Isolation resistance VIO = 500 V dc at TA = 175 C (Tsi) Ris MIN. 10
9
Symbol
Speck
Unit
IV III 55/100/21
UIORM Upr Upr
890 1 068 1 424
Vpeak Vpeak Vpeak
UTR
8 000 2 > 7.0 > 7.0
Vpeak
mm mm
CTI
175 III a
Tstg TA
-55 to +150 -55 to +100
12 11
C C
Ris MIN. Ris MIN.
10 10
Tsi Isi Psi
175 400 700
C mA mW
18
Data Sheet PN10235EJ03V0DS
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
When the product(s) listed in this document is subject to any applicable import or export control laws and regulation of the authority having competent jurisdiction, such product(s) shall not be imported or exported without obtaining the import or export license.
* The information in this document is current as of March, 2006. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products and/or types are available in every country. Please check with an NEC sales representative for availability and additional information. * No part of this document may be copied or reproduced in any form or by any means without prior written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document. * NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC semiconductor products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC or others. * Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. * While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. * NEC semiconductor products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. The recommended applications of a semiconductor product depend on its quality grade, as indicated below. Customers must check the quality grade of each semiconductor product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness to support a given application. (Note) (1) "NEC" as used in this statement means NEC Corporation, NEC Compound Semiconductor Devices, Ltd. and also includes its majority-owned subsidiaries. (2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for NEC (as defined above).
M8E 00. 4 - 0110
Data Sheet PN10235EJ03V0DS
19
PS2562-1,PS2562L-1,PS2562L1-1,PS2562L2-1
Caution
GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. * Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. * Do not burn, destroy, cut, crush, or chemically dissolve the product. * Do not lick the product or in any way allow it to enter the mouth.
For further information, please contact NEC Compound Semiconductor Devices, Ltd. http://www.ncsd.necel.com/ E-mail: salesinfo@ml.ncsd.necel.com (sales and general) techinfo@ml.ncsd.necel.com (technical) Sales Division TEL: +81-44-435-1573 FAX: +81-44-435-1579 NEC Compound Semiconductor Devices Hong Kong Limited E-mail: ncsd-hk@elhk.nec.com.hk (sales, technical and general) FAX: +852-3107-7309 TEL: +852-3107-7303 Hong Kong Head Office TEL: +886-2-8712-0478 FAX: +886-2-2545-3859 Taipei Branch Office FAX: +82-2-558-5209 TEL: +82-2-558-2120 Korea Branch Office NEC Electronics (Europe) GmbH http://www.ee.nec.de/ TEL: +49-211-6503-0 FAX: +49-211-6503-1327 California Eastern Laboratories, Inc. http://www.cel.com/ TEL: +1-408-988-3500 FAX: +1-408-988-0279
0504
4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix -A indicates that the device is Pb-free. The -AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL's understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information.
Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*)
If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL's liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.

▲Up To Search▲

Price & Availability of PS2562L-1-F3-A

	To Download PS2562L-1-F3-A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .